PIC16F737-I/SP【PDF 82/231 页】IC PIC MCU FLASH 4KX14 28DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3841

78页 79页 80页 81页 [82页]83页 84页 85页 86页

PIC18F2X1X/4X1X

DS39636D-page 178

2009 Microchip Technology Inc.

16.4.6.1

I2C Master Mode Operation

The master device generates all of the serial clock

pulses and the Start and Stop conditions. A transfer is

ended with a Stop condition or with a Repeated Start

condition. Since the Repeated Start condition is also

the beginning of the next serial transfer, the I2C bus will

not be released.

In Master Transmitter mode, serial data is output

through SDA, while SCL outputs the serial clock. The

first byte transmitted contains the slave address of the

receiving device (7 bits) and the Read/Write (R/W) bit.

In this case, the R/W bit will be logic ‘0’. Serial data is

transmitted 8 bits at a time. After each byte is transmit-

ted, an Acknowledge bit is received. Start and Stop

conditions are output to indicate the beginning and the

end of a serial transfer.

In Master Receive mode, the first byte transmitted

contains the slave address of the transmitting device

(7 bits) and the R/W bit. In this case, the R/W bit will be

logic ‘1’. Thus, the first byte transmitted is a 7-bit slave

address followed by a ‘1’ to indicate the receive bit.

Serial data is received via SDA, while SCL outputs the

serial clock. Serial data is received 8 bits at a time. After

each byte is received, an Acknowledge bit is transmit-

ted. Start and Stop conditions indicate the beginning

and end of transmission.

The Baud Rate Generator used for the SPI mode oper-

ation is used to set the SCL clock frequency for either

100 kHz, 400 kHz or 1 MHz I2C operation. See

Section 16.4.7 “Baud Rate” for more detail.

A typical transmit sequence would go as follows:

The user generates a Start condition by setting

the Start Enable bit, SEN (SSPCON2<0>).

SSPIF is set. The MSSP module will wait the

required start time before any other operation

takes place.

The user loads the SSPBUF with the slave

address to transmit.

Address is shifted out the SDA pin until all 8 bits

are transmitted.

The MSSP module shifts in the ACK bit from the

slave device and writes its value into the

SSPCON2 register (SSPCON2<6>).

The MSSP module generates an interrupt at the

end of the ninth clock cycle by setting the SSPIF

bit.

The user loads the SSPBUF with eight bits of

data.

Data is shifted out the SDA pin until all 8 bits are

transmitted.

The MSSP module shifts in the ACK bit from the

slave device and writes its value into the

SSPCON2 register (SSPCON2<6>).

10. The MSSP module generates an interrupt at the

end of the ninth clock cycle by setting the SSPIF

bit.

11. The user generates a Stop condition by setting

the Stop Enable bit, PEN (SSPCON2<2>).

12. Interrupt is generated once the Stop condition is

complete.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式